Parcel IDs · North Carolina · November 18, 2026
North Carolina PIN Number: How the 10 Digits Work
A North Carolina PIN is built from State Plane coordinates of the parcel's center. How to read the 10 digits, the condo suffix, and where to look one up.
In most North Carolina counties the parcel number is not just a label. The PIN (Parcel Identifier Number) is built from the parcel's location: the North Carolina State Plane coordinates of a point near the middle of the parcel. If you know how it is made, a PIN tells you roughly where the land is.
How a North Carolina PIN is built
The Secretary of State's Land Records Management program sets the method in its best practice manual for county cadastral mapping. The steps, using the manual's own example:
- Measure the coordinates of the parcel's visual center on the parcel map: easting 2,715,569 and northing 756,737 (feet, NC State Plane). The northing is written with a leading zero, 0756737, so both numbers have seven digits.
- Pair the digits. Take the first digit of the easting with the first digit of the northing, the second with the second, and so on: 20 77 15 56 57 63 97.
- Keep the middle five pairs and drop the first and last pair. The result is ten digits, written 7715-56-5763.
| Easting digit | 2 | 7 | 1 | 5 | 5 | 6 | 9 |
|---|---|---|---|---|---|---|---|
| Northing digit | 0 | 7 | 5 | 6 | 7 | 3 | 7 |
| Pair | 20 | 77 | 15 | 56 | 57 | 63 | 97 |
| Used in PIN? | dropped | grid | grid | block | lot | lot | dropped |
The manual names the parts: 7715 is the grid number, 56 the block number and 5763 the lot or parcel number.
Because each pair holds one digit of each coordinate, you can read the sizes straight off the method: the four-digit grid number places the parcel's center in a 10,000-by-10,000-foot square, the block number in a 1,000-foot square inside it, and the last four digits in a 10-foot square. The dropped last pair is the one-foot digit.
A real example: the State Capitol
In the statewide parcel layer on NC OneMap, the Capitol Square parcel at 1 E Edenton St in Raleigh (Wake County) has PIN 1703-79-0137. Un-pairing the digits gives an easting of about 2,107,03x feet and a northing of about 739,17x feet. The parcel's mapped outline in State Plane feet runs from about 2,106,778 to 2,107,316 east and 738,888 to 739,428 north, so the point the PIN encodes falls inside the parcel, as it should.
The same record also carries a separate county account number. The state manual says the PIN is the preferred parcel ID but does not have to be the only one, or the key a county uses to link its appraisal system to the map.
Rules that come with the PIN
- Unique in the county. No two parcels in a county may share a PIN. PINs repeat between counties, so always pair a PIN with the county name.
- Condos and other units get a three-digit suffix after a decimal point, .001 to .999. The manual's example is 7715-56-5763.001.
- Splits and combinations get new PINs. A PIN stays with a parcel as long as it is not subdivided or joined with another parcel. The manual asks counties to keep a retired-parcel layer with the old outlines and their retired PINs, and the numbering system must show which parcels a new one came from.
- Registers of deeds can index by PIN. Under G.S. 161-22.2 a register of deeds in a county where every parcel has a unique PIN may, with the Secretary of State's approval, index recorded instruments by PIN instead of only by name. Among the conditions: each PIN must reflect the State Plane coordinates of a point in the parcel or be keyed to a map showing its location.
What about the new 2022 State Plane system?
The National Geodetic Survey is replacing the 1983 State Plane system with a new one. North Carolina's datum planning materials list the parcel numbering system among things to preserve and propose conversion equations so that PINs made from new coordinates stay consistent with existing ones.
Where to look up a North Carolina PIN
- NC OneMap statewide parcels: a free statewide parcel layer that includes each county's parcel number.
- The county GIS or tax office: the most current ownership and value. Our North Carolina page lists each county's official map.
Open NC OneMap parcels North Carolina county GIS maps
For background on the coordinates themselves, see what a State Plane coordinate system is.
Open the Platbookmapper county map Browse the county GIS directory by state
Not a survey. County GIS and tax parcel maps are assessment and planning layers. They are not a substitute for a recorded plat, deed, or licensed survey — especially for fences, setbacks, or boundary disputes.
Related guides
- What is a State Plane coordinate system?
- What is an APN number?
- Vermont SPAN number
- Maryland property account number
Sources
- NC Secretary of State, Land Records Management, Best Practice Manual for Digital Cadastral Base Mapping in North Carolina (2016), §11.5 and Appendix B
- N.C. Gen. Stat. § 161-22.2, Parcel identifier number indexes
- NC Secretary of State, Land Records Management Section
- NC OneMap, statewide parcels (Capitol Square record queried Nov. 18, 2026)
- NC Department of Information Technology, 2022 datum presentation (NC 2022 PIN conversion)