Platbookmapper County GIS Directory

Blog · October 17, 2026 · Washington

Using the Colville Flood Zone Map

Flood zones are set by FEMA, and checking one near Chewelah takes a few minutes.

VIEW PLATBOOK MAPPER

A handheld GPS used to walk a rural parcel

Platbookmapper is an Amazon Associate. If you buy through an Amazon link on this page, we earn a commission. The link is a product, not the county map.

Before an offer near Kettle Falls, check the Colville flood zone map: the zone on that map shapes insurance, building rules and resale. In this Colville guide: finding the address on FEMA's map, reading the zone codes, and pairing it with the Washington Current Parcels layer in ArcGIS Map Viewer.

Getting started with the Colville flood zone map

Start with FEMA's Flood Map Service Center: type an address near Springdale, then open the map view for that panel. A tract near Chewelah without an address can still be found: pan from the closest town then click the parcel area.

The free map to start with

Begin with the Washington Current Parcels layer in ArcGIS Map Viewer; it includes every tax parcel from Kettle Falls to Springdale. Around Chewelah, type a street address, an owner's name or a parcel number, and the viewer zooms to the match. Closer to Chewelah, write down the parcel ID while you have it open; each office in the county uses it to find the file.

Before you lean on the lines

Parcel lines are drawn for taxes, not measured on the ground, so the edge of a yard near Chewelah often sits some distance off the line on screen. If you're looking near Chewelah, records update in batches, so a deed recorded last month can take weeks to appear.

On site with the map

The parcel map usually runs in a mobile browser, which helps when you're standing on land near Chewelah, but coverage can be spotty out of town. A screenshot of the parcel near Chewelah with its ID keeps working without signal.

City limits and county records

Colville sits in Stevens County, Washington, and the county assessor maps its lots. As the county seat, Colville hosts the courthouse, handy when you need recorded documents. In and around Northport, city or town hall handles things like zoning, permits and utilities for lots inside the boundary, and the county still keeps the parcel and deed records. Land beyond the town limits toward Chewelah often follows county rules rather than the town's.

Recorded documents worth pulling

For anything that matters, pull the recorded deed from the County Auditor; the parcel map near Chewelah only summarizes it. Long-held tracts near Kettle Falls can sit on many deeds, and a title company earns its fee before a purchase.

What the zone letters mean

Zone AE carries a published BFE, which plain A zones lack; that elevation drives building rules near Marcus. For a home near Chewelah, a shaded X area is moderate risk, between the 1% and 0.2% annual chance floods; plain X, or C on older maps, means minimal mapped risk.

Parcel lines plus flood zones

FEMA's map shows zones but not ownership, so open the Washington Current Parcels layer in ArcGIS Map Viewer next to confirm you have the right parcel near Marcus.

When a parcel crosses a boundary

Stevens County touches Ferry County, Lincoln County, Pend Oreille County, and Spokane County, all with their own assessor records. Acreage along the edge near Chewelah can show up in two county records, so look at the neighboring map before you assume the acreage. Near Marcus, the Platbookmapper state page links each neighboring county map for Washington.

Who handles what

Recorded documents for a parcel near Chewelah are with the County Auditor, usually searchable by name or document number. Questions about what you can build around Springdale are for the local planning and health departments, town or county, depending on location.

Beyond the mapped zones

Low-lying fields near Springdale aren't always studied in detail, so look for water marks and debris lines. Marshy spots near Springdale can limit building too; the National Wetlands Inventory mapper shows mapped wetlands.

Stevens County in a few facts

Colville holds the county offices, home to the main records offices. You'll also find Kettle Falls, Marcus, Chewelah, and Northport, where town lots give way to larger tracts. About 48,837 people live in Stevens County (Census estimate, 2023) on about 2,477 square miles. Stevens County dates to 1863, which matters when you trace an old farm's title. Landmarks such as Colville National Forest are easy to spot when you zoom out from Kettle Falls.

Insurance, lenders and building

On ground around Chewelah, ask for an Elevation Certificate: it records the building's elevation against the base flood. Remodeling a house in a zone near Kettle Falls usually means extra permit review; check with the county or town building office early.

A short flood checklist

Request whether the home has flooded for the house near Marcus; an insurance quote early avoids surprises.

Frequently asked

Is flood insurance mandatory near Springdale?

Short answer: lenders generally require it for buildings near Kettle Falls in a Special Flood Hazard Area when the loan is federally regulated or insured; elsewhere it's optional.

What is a base flood elevation near Northport?

Generally, a BFE near Kettle Falls tells builders how high the lowest floor should be; local rules may require building above it.

Is there a flood layer on the parcel viewer near Springdale?

Generally, a flood layer may appear in the Washington Current Parcels layer in ArcGIS Map Viewer layer list, but FEMA's own map is the official source.

Can a flood zone near Kettle Falls change?

In most cases, zones near Marcus can shift when FEMA updates a panel; check the effective date on the panel.

Is there a way to export the map near Chewelah?

Use the print button or a screenshot; include the record panel for the lot near Kettle Falls.

Open the official Stevens County, WA parcel map See it in the Platbookmapper directory

Related

← All posts · Open the map